Category: OIL PARQUET

Parquet oil used for wood flooring in the form of, Floorboard, stair steps, countertops. This oil can now speak good alternative varnish for parquet. In such cases, (wood floor finish) for decorative woodworking needed the most resistant to wear oils and oils with waxes, than oil for furniture. In this product category most penetrating oils have it without wax, oil and wax (hardwax oil) allow you to create visually appealing layer on the surface of your wood products .

Training (grinding) wooden parquet under the application of oil.

"Prepare the wooden surface for the application of oil".

The oil should be applied to previously untreated wood. All kinds of impregnation, Primer, varnishes closed pores of the wood and create a layer of film, which does not penetrate through the oil timber and permeates. If you want to change the color of the wood and then applying oil, This can be done with the stain CLOU или Trae Lyx. Clow stain or Trae Suite only change the color of the wood and do not create a protective film, allowing color is applied to any wood oil, wax or polish. Let's take each question will be taken up sequentially .

Pre-sanding the floor.

Any surface before applying oil for wood be sure to grind. The surface must be sanded with the grain. Sanding wood across the grain is not welcome. Sanding could scratch. If you shlifuete along the grain, acquired timber installed scratches on the wood structure and the further processing of their negligible. If you are grinding on your wooden cross product will crack and you do not remove them, then for further processing, especially colored oil are very manifest and will beat you in the eye. Be sure to clean the wood surface clean of dust from sanding. If you want to apply oil on wood, which had been previously treated, See recommendations in the article "The restoration of natural parquet , wood and laminate ". More please, if you have that option, put oil on the wood immediately after grinding , because in this time of grace wood pores are open and you can get the most out of manifestation wood grain.

Methods of surface preparation for the application of the same oil to the floor or furniture will be different.

For example, for the preparation of parquet floor sanding basics first performed using a drum sander with sandpaper number P 40 . After that, again using a drum sander a second step is polishing, but with the grain number P 80. You can of course between these stages to make an intermediate sanding sanding with sandpaper grain number 60. But it is as you like, not a dogma. So , on this work with a drum sander on a given surface we finished. The next stage of our preparatory work is to perform polishing of parquet with orbital sanders and sandpaper s grain number P 80. After that perform well on the grinding surface grinding machine , but already using sandpaper with a grain number P 100. For now the Surface grinding machine for wood flooring for the application of oil over. But this is not the final preparation. Now we need to have in the arsenal of so-called planetary grinder. On one engine, this car is three or four disks. Planetary she called because, that each disk rotates on its own, like planets. This option allows the planetary grinder to achieve , it can be said, perfect quality polishing the surface. Finish sanding the parquet with a planetary machine eliminates all kinds of risochki , scratch ( that is just what we need). All anything, You'll open the parquet lacquer. Then no need to finish sanding machine planetary. But in the case of oil - special situation. Oil on the floor is showing scratches, chipped. Especially colored oil, Draw a very bright here these scratches, that you leave on the floor during the grinding. So to the question of training under the parquet subsequent deposition oils, especially color, Please keep an seriously.

The next phase of our work on the preparation of parquet – polish.

Polishing we can do the same with orbital sanders. Polish using a grid with a grain number 120 above. It is the finishing stage of preparation for the application of the parquet oil. Still need to take a vacuum cleaner to remove dust and, Clean the surface well. Now your flooring is ready to spray colored oil Bring-Luxury PRO COLOR . All, we are here to recommend you a parquet , certainly not going to do on the stairs, furniture facades and other wooden stakes. For furniture, doors , facades simply by hand or by using a small grinders grind the grain to perform for 1 or twice , in this case the grain sandpaper will 180-320.

I wish you every success in the preparation of parquet and other surfaces for the application of oil and oil with hard wax.

White stain wood products.

White stain for toning wooden furniture, flooring and stairs.

 

Fashion trend in the construction and design of persistently direct you thinking to make flooring or walls, furniture in white. Great idea, goal is set, let us understand the possibilities to make the dream a reality. Just want to tell you, my dear readers, it would be just a generalized article about materials for “whitening”, which can be described in one word : white stain.

So the first and basic division (it will simply be a completely different system of woodworking) whether processed white products are in the interior or will it be street ( outer coating).

If we need to cover interior wood , in this case, there is a wide selection , depending on the desired effect , we want to get from the whitening of wood.

So, for example, task, to white painted wood time only , and themselves solid wood fibers retain their natural color , ever had any - any other color. This effect has selected wood in white color on the treated surface can be achieved with hard wax oil Trae Lyx Pro color Wit. Hardwax_white

( The link – more articles of different oils with wax on wood )

Just look at the photo. If the same product is applied to the surface of the wood, which was previously tinted water-stained wood, например Trae Lyx или CLOU, then the wood will have a color stain, and only the wood pores will be white.

Белая морилка : масло с твердым воском белое

Oil with white hard wax (white stain) . Ash

However, we must take into account, that treated wood must certainly have deep pores , pronounced relief wood structure. If the tree does not have the properties of nature, structure can make art (artificially) , mechanically, with special brushes to choose soft fibers.

Creating a white floor , various methods can be used to achieve a variety of results, so, nanensnii such as white oil with wax Trae Lyx turned a bleached floor:

белый лак для дерева и деревянного пола.

Floor (дерево ясень) покрыт белым маслом с воском Trae Lyx Wit.

Oil wax white and can be applied by machine:

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

White water-borne wood stain.

If it is about, to white paint not only the pores, a plane full of wood , in that case can use white “aqueous” morilku , such Trae Lyx color stain white parquet number 2537. Of course, as there is a very large choice of stains.

Белая морилка для дерева Trae Lyx

White stain for wood water : Trae Luxury, Netherlands

More details Stain Trae Lyx will be discussed in another article. However, focus your attention on this fact, that the use of water stains included mandatory subsequent protective layers of lacquer , Oil , oil with hard wax or wax.

Oil with white wax.

 

Just one option whitening wood in the interior there is oil with a solid white wax, for example , Golden Wave . I want to clarify , that this product is based on centuries-old recipes of old Scandinavian tradition. In this embodiment, the product is applied 2 or 3 The product's , depends on the degree of whiteness and looking through the tree . Additionally, on a hard wax oil as an anchor layer did not need to put more. This product is finishing. More detail with the process technology, and photos can be found in the article "How to make a white floor". Also when using a white hard wax oil from Golden Wave can change the color of the wood previously with water stains Trae Lyx or CLOU , and then apply the oil with wax. However, you may achieve a certain effect of whitening your own unique timber.

White primer for wood.

 

The next version of the whitening of wood - use special primer Trae Lyx PROJECT SEALER 2K wit - insulating undercoat white parquet. The use of this white soil provides for the mandatory application of the two-component varnish Trae Lyx Project. Of this product is discussed in detail in this article "Nail flooring and stairs" . This combination of lacquer designed for those who appreciate high quality and reliability of finishing top coat for natural flooring and wooden stairs.

Natural wax white.

The next version of the whitening natural wood - use white wax Golden Wave. This product use for furniture , walls , Ceiling ,Beams , railings and other wooden surfaces , are not subject to high loads in the interior.

Golden Wave color white wax - is wax in turpentine, Portugal made of natural wax and special pigments. With this unique color white wax on untreated wood can quickly and easily create a subtle effect. For more on this we said in the article "Waxing colored wax".

White paste for aging wood.

 

Another option is a custom whitening wood , I think , What did you like. This kalkpasta. Creates the effect of a very old , whitened by time and the old tree. Used it for both internal,, and outdoor products. With respect to other materials for whitening wood kalkpasta applied for stairs , parquet , Furniture , windows , shutters , doors , homes , arbors, swings, etc.. More details about kalkpaste we said in the article "Furniture antique calc-paste".

If we need to finish for exterior wood effect whitening , then we can also consider the following options.

White stain on the basis of liquid wax.

Bleaching of wood with wax protective stain white Verfijn Steigerhout beits . Using this product , Do you feel , that go "back to nature" . Stayzherhaut stain white emphasizes the authentic look of natural wood , moreover , Stayzherhaut stain-defender has a gorgeous wood from sineniya and decay over time.

White paint for wood.

 

Whitening effect of wood are also, applying the coating and film-forming. Now this in more detail.

As a primer , which at the same time will have the status of a white stain , You can apply Sigmalayf VS-X. This is a protective stain alkyd based. When using the VS-X Sigmalayf treated wood for a long time to receive protection from the elements and UV. As a finishing coat on Sigmalayf VS-X can be applied as an acrylic blue acrylic Sigmalayf DS , and extremely high quality lacquer alkyd based Avis timberkoat. I draw your attention to a distinctive positive Sigmalayf VS-X. Wood , treated with this product may be a long time to be in the open air , outside in bad weather without finishing. And the wooden surface will not be harmed.

This is not a complete list of methods, using which you can create the effect of whitening wood. However, in his article, I use information on materials , I have personally tested and tested. If you have a task "as whiten the wood", I'd be happy , that my advice helped you at all 100 % .

Your consultant.

How to paint a wooden floor in a private house

What color wood floor

in a private home.

Let's, talk on the subject, What are all the same and how to paint a wooden floor? Lacquer or wax oil?

Suppose, in your house are made from natural floors flooring.

This is an old board, which was covered by some type of enamel or lacquer PF, but the cover eventually fell into disrepair, has a worn look and seat covers were worn to a tree. Just thinking , that the old wooden floor only once painted brown paint shivers run down the spine. A completely change the floor board to the new is not comparable to your financial plans.

Do not panic, there is a great option for your case.

Now, let's detail at this point stop. You must first define, what material was made your wood floor.

Properly think, must completely remove the old paint, ie scrape.

At this point we will not linger , move on. Here the surface of the board ottsiklevana , has a natural look. Suddenly you define , that the floor boards made of pine.

Сосновая доска пола перед покраской

Pine wood floor.

Pine , known , softwood and under certain load changes the geometrical parameters.

Well, suppose, Do you like, to floor board was lacquered .

You have good taste, but not every paint can cover a pine wood floor. And here's the thing. Traditional parquet lacquer is not suitable for handling the floor boards of softwood , because parquet lacquer creates a solid film, and pine - soft wood. Under load, eg heels shoes, pine board flex, compressed, formed on the surface of the board dent. A parquet lacquer - the material is hard and does not have the elasticity , that together with the pine board to change its geometry and repeat profile dents on board. First, in this place there is a small crack, invisible to your look, then it begins to crack constantly splashing ( time to wash the floor), begin the destructive processes seem such a beautiful lacquer floor, which seems to be not so long ago was polakirovan. And in the end, climb round coverage beginning.

Therefore cover the wooden floor of softwood conventional parquet lacquer not! For this floor boards should be used to paint just this purpose, "For a soft wood" or "for the floor boards». Here , for example , see photos.

Лак для деревянного пола TRAE LYX

Nail pine floorboards

On the original packaging with the varnish must be necessarily specified, that the paint used for such surfaces of soft wood. In this case, floor board , the uncovered "nail the floor boards" will be a very long time to keep a seal coat. Nail soft wood has excellent flexibility and strong property with wood under load applied geometry wooden surface. And pine board of which will make your wood floor, treated with varnish for softwood, not inferior in performance to wear surface which is made of solid wood. Just for each wood product should be used for other purposes, as the saying goes, "the doctor ordered". It is not just , such as manufacturer of parquet lacquer TRAE-LYX in Holland invented separately parquet lacquer ( this is for solid wood ) and separate nail flooring ( this is for soft wood). And in the case of a parquet lacquer necessarily used as the first layer of soil is , and after the deal 2 varnish layer. We spoke about it in another article “Varnish for stairs”. And in the case of painting the floor boards of soft wood should be applied three coats of varnish to the floor boards directly on the tree , without primer. So you see , Even Coating technology depends on , of every tree of your floor is made.

So , our wooden floor of pine floor board plot the three layers TRAE – LUXURY BODEN LAK.

The result is a beautiful wood floor .

Let us choose the nail flooring softwood from a wider range. So, for example, TRAE-LYX nail softwood is an aqueous acrylic-polyurethane. Especially its composition as applied guarantee maximum environmental friendliness, the speed and performance of the total volume of paint work, the absolute lack of smell, perfect transparency and , as our main goal, long service life of wooden floor boards at the highest levels of activity.

A viable alternative when choosing a nail flooring softwood ( pine, fires and others) can be called lacquer Sigmavar c2 SIGMAVAR S2U. Unlike TRAE-LYX varnish Sigmavar c2 is a urethane modified alkyd based. A distinctive feature of Sigmavar c2 from conventional urethane alkyd varnish is its enormous resistance to mechanical stress. It is more robust and less sensitive to shocks, more resistant to scratches and abrasion, than ordinary urethane alkyd varnish. I specify , Sigmavar c2 that has a specific purpose - for finishing wood surfaces, exposed to mechanical stress active indoors. Also in contrast to the conventional urethane alkyd varnish Sigmavar c2 does not cause yellowing of wood, maintaining almost natural color of the wood.

In comparison with Trae Suite varnish Sigmavar c2 has a longer drying ( 24 hours between coats), therefore, to perform a full system varnishing Sigmavar c2 in three layers must be a minimum of three days.

Same , If these two products compared to the presence of odor, Trae Suite - absolutely no odor and the room immediately suitable for use. Sigmavar c2 is of course a faint smell when varnishing. Given The, that drying varnish Sigmavar c2 dust 2 o'clock, within this time and after ventilating felt almost no odor.

Just when choosing a nail floorboards note, that Trae Suite and Sigmavar have a significant difference for the price. If you want to quickly perform work on varnished parquet, ladders or other products made of soft wood and it is in your opinion should be an aqueous varnish, then it Trae Suite. If you have left more time to perform work on varnished wooden surface , this may not necessarily be aqueous varnish and you plan to spend on nail modest amount of money, then use Sigmavar c2. Both of these products are manufactured in the Netherlands, have high performance and well established in the application and operation.

Let me repeat to you useful information , you're welcome, Pay attention to this. If you have decided to apply specifically urethane alkyd varnish for wood flooring, Pay attention to the instructions in the packaging and material. It should be urethane varnish based on modified alkyd, that is, a modified alkyd varnish, which can be used in dwellings. Look at the picture, on the bank is required to have relevant information, for example on the packaging Sigmavar c2 here such an icon - a small house inside arrow, that is, for indoor use.

Этикетка алкидного модифицированого лака Sigmavar S2U

The label on urethane alkyd modifitsirovannomlake Sigmavar S2U

Let's look at another option wood floor finishes. I suggest you handle the floor board of pine oil with hard wax , which , including, intended for the floor boards of softwood . This product TRAE – LYX HARD WAX PRO MAT . The fact , the oil wax or oil does not create a film , therefore, these products are perfect for processing pine floorboards . Remember , under load soft wood shrinks , dents formed . Oil wax or oil is not just a form films , obluschivatsya nothing !!!

Деревянный пол : Сосновая доска пола.

Dent in the pine floorboards

Even if the wood is subjected to strain , the coating still remains intact. But again , need to face the truth.

Not all products are called wax oil have strong features and truly fulfill its purpose , especially in the case of finishing the floor boards of softwood.

Let's take a closer look at the question of choice oil-wax pine floorboards.

For example, surface pine floorboards kept under light foot traffic, that is, it ,perhaps, Bedroom , library, cabinet. In this case it is possible to apply the hard wax oil Veyf Golden Matt. This product is manufactured according to the recipes of old Scandinavian traditions based on natural oils and natural waxes. Look at photo, how noble vyglyaditpoverhnost covered with pine floor boards this material.

Пол в частном доме легко покрасить не лаком а цветным маслом с твердым воском Golden Wave/

On the floor of pine boards coated with wax color oil

More photos appearance wooden floor made of pine, which is painted with oil wax for wood:

Сосновая доска, деревянный пол покрашен цветным садовым маслом и потом покрыт маслом с твердым воском матовым Golden Wave.

View of pine wood floor under oil with wax.

But, if still in the room involves extensive use of wood coatings, then still it will be better to use an oil-wax line Trae-Suite or naturel Oliya Golden Veyf, which composition comprises a polyurethane additives, cured by UV and has a special meaning resistant to abrasion and abrasion coating. In the picture it looks like this.

Иносостойкое покрытие, не лак для паркета, а масло для дерева: Golden Wave Naturel Olie.

Surface, requiring high wear resistance, Oil painted with polyurethane.

About , how to determine the choice of oil-wax we also said in another article “Oil for stairs”.

Here's a look at the pictures as the board looks different from pine oil , that , in my opinion , can safely be used to trim the floor boards of softwood.

 

Трае Люкс масло с твердым воском на сосне : деревянный пол или стены.

Butter with wax Trae Lyx satin of the pine wood floors or walls.

Паркетное масло Трае люкс на сосновый деревянный пол или стены

Parquet oil Trae Lyx the pine wood floors or walls.

Масло с твердым воском матовое Трае Люкс на деревянный пол

Matte hard wax oil with Trae Lyx the pine wood floors or walls.

 

Масло с воском белое Голден Вейв

White oil with wax on the pine

Or here looks like wooden flooring of ash, covered with a durable hard wax oil white Trae Lyx Pro Color:

Белый лак для дерева можно легко заменить на белое масло с воском для пола Trae Lyx Hard wax Pro color.

Paul Ash covered durable white oil with wax Trae Lyx.

By the way , looks like a beautiful white floor , we discussed in another article “How to make a white floor”.

If you want to give the oak wood floor or stairs beautiful antique appearance: You can use Calculator paste.

The photo turned out of the ordinary oak stained oak.

Старинный деревянный пол из дуба

Oak wood floor, aging calc-paste

On the application of calc-paste aging furniture in the style “Provence” we learned about in another article: “Artificial aging…”

So what determines the view topcoat for your flooring , Ask questions , discuss them and work out together.

Your consultant.

Oil for wood stairs

Oil for stairs

Let's talk about , how to determine the choice of natural wood varnish : Oil for stairs. Stair treads are subject to intense stress and so on the steps of coating wears away faster, than on the same landing, or just on the floor in the room. The main abrasive, that first scratch topcoat stair steps, and then sometimes just grind it to zero – this is the most common sand , we together with shoes is brought into the house.

Of course, the most powerful protective coating steps gives special varnish for stairs , we talked about this in another article of varnish stairs .

However, the task of finishing steps for stairs is oil or oil with wax . Lacquer coating is like a little cut eye, want something for the soul. Of course, because varnish creates a film, and the butter or oil - wax film does not create, wood remains as if no cover, however, protected against dirt and the sand and abrasion.

That is an objective truth, nature itself protects the native.

I understand you perfectly, because it is the product, coated with oil or wax looks like that noble breed, there is a sense of natural warmth from nature.

Oil for stairs or oil-wax?

The next step, we must decide, What are we going to use:

oil or a mixture “oil-wax” to tree?

Let's start from the reverse, what we want to get the result.

If it is about the maximum to protect the wood from getting wet, bugs and strengthen timber, in that case you have to use oil. Most oil penetrates deep into the wood, impregnates her and strengthens, it strengthens, as the oil solidifies in the wood. Oil, in turn, differ in their category in the depth of penetration into the wood. And the deeper oil stairs nestles, the greater the flow rate is obtained by 1 square meter of surface. So, например масло GOLDEN WAVE тиковое, Oil is the deep penetration, its consumption is 10 m. with 1 liters and this oil with natural properties can be used to protect, treatment and restoration of wooden terrace and garden furniture. Other oil, for example , TRAE-LYX PARKET OLIE parquet oil has different features and benefits, more this oil we said in the article "a pronounced effect of wood" ,

This oil has a wonderful property for rare oils 100 % solid component, that is, all the oil, you have put on the wooden surface and is absorbed into the tree, hardens and greatly strengthens the wooden surface. Even soft woods, treated in this oil, become hard. In this embodiment, the surface treatment of wood, it can be said, produce a "concrete" and at the same time extraordinarily beautiful , See all photos in the same article.

Natural oil for stairs:

If the task is, to the ladder after finishing oil or oil-wax to preserve the color of natural wood, can in this case be used safely GOLDENWAVE NATURELOLIE (Natural oil). This unsurpassed for its magnificent natural characteristics of the product remains the primary color of natural wood. Natural Oil Golden Veyf has in the additive polyurethane, thus creates a very resistant coating to wear and abrasion, what exactly is required for a foot of stairs. Just natural oil Golden Veyf posing on the machined surface finish light shine, there is a feeling, it lacquer surface, however, in reality it has film, see photos:

Дубовая лестница покрашена не лаком а маслом для дерева Golden Wave.

Balusters, oak staircase, natural oil Golden Wave.

Or here's another picture element of oak stairs, so coated with natural oil:

Ступени лестницы из дуба покрыты не лаком для лестницы а натуральным маслом с полиуретаном Golden Wave.

Oak steps are also not covered by lacquer and natural oil.

Just "natural oil" Golden Veyf has the distinctive feature of the brand's other oils, as they say: "Dries in a brush", it is completely without leaving absolutely no divorce, Borders , transitions, sagging, etc.. Shrouded in normal home or stair baluster natural oil Golden Veyf with a brush has the form, as if this item is painted in a super modern spray booth or using dip. Moreover, Natural oil Golden Veyf absolutely has no odor. When using this natural oil has a nuance, about which we should not forget. If you are not completely used oil from the jar, make sure that, to cap tightly closed jar. If the jar is closed tightly, the residual oil solidifies therein very quickly (possibly per day), because it is a natural oil Golden Veyf cured by exposure to light.

Look at photo, how perfectly preserves the natural color of the oak GOLDENWAVE NATUREL OLIE:

Для покраски лестницы из дуба выбрать не лак а масло для дерева и лестниц.

Oak staircase in a private house covered with natural oil durable Golden Wave Naturel Olie.

Butter with wax for stairs:

If the task is , Steps had to look and chic furniture polish , then you need to apply the oil with hard wax matte or satin . Hard wax in the product, in this case allows the surface to have a polished look. With hard wax oil is also frosted, for example, TRAE-LYX hard wax PRO MAT или бывает с блеском атласа ( satin), например TRAE-LYX hard wax SATIN. Look closely at the photo , where clearly visible difference in gloss.

масло для лестниц: Масло воск Трае Люкс сатин

With hard wax oil for wood flooring and stairs satin Trae Lyx


Слева сатиновое масло-справа матовое масло с воском TRAE LYX

From left to right, satin matte oil-wax oil TRAE LYX

With regard to surface maintenance , обработанной маслом или масло -воском , here you need to use the product TRAE-LYX «care oil- wax " . This wax , which is soluble in water . It is added 40-60 ml 6 liters of water. And this water just washed the floor , ladder , furniture. As a result, use of the product TRAE-LYX «care oil- wax "wooden surface oil or wax-updated , micro scratches disappear , because wax , dissolved in water to fill , In addition the surface acquires property "anti slip" , that is important for the stairs . The same surface becomes property of "anti slip" dirt.

I hope , that my article will help you choose the right oil is needed for you to stairs and you will have the best result !

The choice is yours, Your consultant.

Oil wax Trae Lyx for finishing wood.

Why wood- oil with wax Bring Luxury ?

The use of natural oil with wax Trae Lyx- it is the norm for your wooden floors and parquet.

Can be difficult to choose from the many offers exactly the material , that is to your liking. The reason is simple , You do not have information about the finest products , that are designed just for you , our dear lovers of wooden floors.

I will try to help you with the definition of the product selection .Масло с воском :Масло воск TRAE LYX Hard Wax PRO

Water stain for wood : parquet, Furniture

Stain Wood : as tint (starve) timber.

If your flooring or natural floor boards or furniture has a natural color, and you have a desire to change the existing shade , This can be done using color tinting, example CLOU or TRAE LYX-. Similar toning (changing the color of the wood) money is nothing, as mordant for wood.

 

Порошковая водоразбавляемая морилка для дерева

Stain Wood. Applying water stains CLOU, Germany.

Preparation of the tree to toning.

Timber should be no cover. If this is a new board , fine . If the tree has been previously handled something , then you need to completely remove the old paint to wood.

Before applying the stain sanded wood grain sandpaper number 180-230. During the 30 minutes after sanding wood has open pores , which closes again after half an hour , tree “breathing”.

Choosing Stains for wood: training.

We take, for example, powder, water-borne stain CLOU, the instructions prepared color solution ( by mixing the powder with hot water + two minutes to mix , stain is ready for use). Proshkurili wood along the grain . Wood surface to dampen some water ( sponge or cloth) , then along the grain proshkurit , take quality brush , for example “Oval brush bristles with Chinese” ,

Кисть овальная для морилки, масла с воском, мебельного лака

Brush Oval stain, oil wax, furniture polish

plot the stain with a brush on the wood along the grain abundantly,

You can watch the video :










how to work with their hands stained. 

Stain wood should be easy to go and exactly , no spots ( is the result of pre-moistened wood).

Морилка для дерева на водной основе.

Water stain on an oak.

If desired, after a certain time to pay a 2nd coat stain. CLOU stain mixed together . So , for example , You can get a trendy color “wenge stain” , by mixing stain CLOU 168 + морилка CLOU 174 in proportion 1:1 , Only the original color is wenge. If you like white shade, it is possible to apply the so-called “beluю morilku”( about this in another article).

Stain is very solidly composition , smallest grinding pigments , so if there is no toning spots , stain without difficulty through all channels and wood fibers, has the effect of , as if the wood in this color rose from nature , supposedly received the tone has a natural basis for proceeding.

In diluted form powder stain wood CLOU has a long shelf life , not damaged. Board , treated stain CLOU , after drying can be treated or painted , TRAE-LUX например или AVIS , but you can oil (Golden Veyf) or butter with hard wax ( Trae-Lux) , or just wax Golden Veyf.

Another article described in detail: how to apply

oil for parquet , or White Oil.

Any covering on the top of the tree or Stain CLOU морилке Trae Luxury will hold well with excellent adhesion.

 

Водная морилка для дерева Trae Ly

Water stain wood Trae Lyx

 

How to make a wooden white floor .

Butter with wax:

WHITE WOODEN FLOOR

I'll tell you, as possible from the ordinary wooden floor or parquet get the perfect trendy white floor, finished color white oil with hard wax.

Деревянный сосновый белый пол .

White pine floor is covered with a hard wax oil white Golden Wave.

 

Wood surface should be covered with no, or varnish, no ground, not impregnated , t. it is. should be an unprocessed. But